The Best Time to Transplant an English Laurel

English laurel (Prunus laurocerasus) is an evergreen shrub or tree that’s a fast-grower, reaching a height of 15 to 30 feet when mature. It does well as a single specimen or implanted in a row to form a hedge. This really is a smog-tolerant plant that thrives in slightly inland coastal locations and grows in U.S. Department of Agriculture plant hardiness zones 6 through 9. If you need to transplant a English laurel, selecting a good time and supplying a bit of extra care before and after the transfer can see to it that the plant remains healthy in its site.

Transplanting in Early Spring

Though it’s an evergreen and doesn’t become fully dormant, the English laurel slows its growth during cool winter weather and becomes semi-dormant during these weeks. It’s best to transfer the plant in early spring, once soil temperature is above 40 degrees Fahrenheit. Do this while the laurel’s still partly inactive but poised to put out fresh roots and top growth — if you analyze dormant buds on several twigs, you’ll notice that they haven’t yet started to swell or show green. Choose a day once the plant’s not stressed from dry weather and the soil is moist. If it’s a massive specimen, run a length of soft twine outside around the plant’s branches, then tying them securely to avoid damaging them during the move.

Tranplanting in Autumn

If your region is in a warmer part of this English laurel’s scope, such as USDA zone 9 and over where frosts are rare and the ground doesn’t freeze in winter, soil temperatures are probably warm enough year round to support root development. In these areas, it is possible to transplant a laurel from the fall and the plant will put out fresh roots during winter. Transplanting in fall also helps the tree prevent the stress of summer heat that a spring-transplanted laurel can encounter soon after it’s moved. If you transfer a laurel from the fall, spreading a 4- to 6-inch thick layer of organic mulch below the plant’s canopy then it’s moved can warm its origins and encourage development of new roots.

Some Preparation Helps

If you have some time before you intend to transfer a laurel, provide the plant some extra attention to help prepare it. Keep it well-watered throughout the season before you transplant, ensuring that it receives at least 1 inch of water weekly, like rain. It also helps to maintain the plant mapped exactly the exact same way after you transfer the laurel to its place — mark a branch that faces north and keep this side toward north in the new site. It’s also very important to keep it at precisely the exact same depth in its new place, to avoid suffocation or drying from origins from planting too deep or too shallow, respectively. Use white paint or weatherproof tape to mark the original soil line on several large branches — make certain that these marks can also be at the ground line following transplanting.

Giving Good Aftercare

After you’ve transplanted a English laurel, keep it well watered, especially during the first few weeks — watch for any wilting of foliage, a sign that it’s not getting enough moisture. Check the top two or three inches of soil regularly and water when it’s dry to the touch, using a soaker hose positioned near the dripline — let water soak till the top 6 inches of soil are moist. If your area will be windy, protecting the plant for its first time with a burlap screen attached to posts driven into the ground around the windy side can help prevent excessive water loss through the foliage. Maintain the laurel well-mulched, but pull mulch away from the lower branches to prevent fungal issues.

See related

Are Miticides Effective on Eriophyid Mites?

Even though miticides efficiently kill the microscopic arachnids called eriophyid mites, the following substances are seldom a smart selection for handling eriophyid infestations. Chemical controls, such as broad-spectrum miticides, can worsen the problem and result in greater damage from eriophyid mites and other insects. Targeted, less-toxic tactics deliver better results if eriophyid mites invade your yard.

Realizing Eriophyid Damage

Plant damage in eriophyid mites shows up in lots of ways, such as bronzed and blistered leaves, deformed growth, along with galls on leaves, stems, buds and blossoms. The unsightly damage generally causes no long-term damage to plants. Native mites exist, but nonnatives are introduced, too. Distinct eriophyid species target certain plants while leaving nearby plants untouched, often going undetected until damage grows. The best weapon against eriophyid mites is a healthy population of beneficial predatory mites. In some cases, eriophyids function as a food source which will keep valuable mites encompassing.

Limiting Broad-Spectrum Miticides

Broad-spectrum miticides kill eriophyid mites, but don’t stop there. Miticides kill all types of mites and may damage beneficial pollinators. Predator mites that kept eriophyids under limited and control dangerous mites, such as spider mites, get killed together with the objective. With predators eliminated, rapid reproduction rates fuel mite populations. Some miticides actually stimulate spider mite production. Even though a broad-spectrum chemical eliminates one eriophyid generation, it produces a predator-free environment for mites that hurt more than just the way the plant appears. Once eriophyid mites get to the gall phase, no treatment is successful. The galls protect the mites inside.

Utilizing Lower-Impact Pesticides

When chronic, unchecked eriophyid populations threaten your plants, horticultural oils and insecticidal soaps may help. Female eriophyids overwinter, then emerge near spring bud break to feed and lay their eggs. Timely applications limit the damage to handy predators. Spray ready-to-use horticultural oil or insecticidal soap seven to ten days before bud break and again as bud break occurs. Cover all surfaces completely with the spray, such as leaf undersides, since the spray must speak to the mites. Spray on wind-free bearings with temperatures between 40 and 90 degrees Fahrenheit, rather than squirt water-stressed plants. Wear gloves and safety goggles, and prevent all contact with exposed skin. Wash your hands thoroughly with soap and water after spraying.

Maintaining Mites in Assess Naturally

Biological and cultural defenses restrict vulnerability to eriophyid mite damage. Encourage predator mites and reduce chemical resistance in insects by not using miticides. Plant mite-resistant cultivars, when accessible, and choose plants well-suited to your climate and soil. Make sure that your plants get the water and fertilizer they need because healthy plants resist pests and diseases better. Eliminate heavily infested plants in the garden, or even prune out affected branches. Eriophyid mites typically spread by wind, but they can travel to dirty garden tools. Sterilize pruning tool blades by wiping them with family disinfectant before and after every cut. Bag and dispose of eriophyid-damaged prunings to avoid spreading diseases or mites.

See related

The way to Transplant the Babies From Ponytail Plants

Ponytail hands (Beaucarnea recurvata) appear like palm trees, and grow up to 30 feet tall in their own native Central America. The crown of foliage droops in the woody, bulbous, erect trunk. Ponytail palms grow outdoors in U.S. Department of Agriculture plant hardiness zones 10 through 11, but they are often grown as houseplants. Baby plants, called offsets, sometimes grow around the base of the mother plant. Each of those offsets can grow into a new plant if you remove them in the ideal way and provide the suitable care.

Preparing the Pot

Ponytail hands root and grow best in well-draining, somewhat dry dirt. Use 6-inch-diameter pots with bottom drainage for planting new offsets. A well-draining potting soil, such as one formulated for cactus or desert plants, provides adequate drainage for fresh ponytail hands, or you can mix equal parts conventional potting soil with sand to make your personal rooting mixture. Use a powdered rooting hormone to guarantee the offsets form roots and set quickly.

Cutting Method

Cutting the offsets in the mother plant in spring is always the quickest way to propagate ponytail palms, but some offsets might fail to form roots and wo not survive. Wipe a sharp knife with a cloth soaked in isopropyl alcohol to disinfect it, then cut the offset in the mother plant just beneath the ground. Dust the cut surface of the offset with an even application of the rooting hormone powder. Pour the rooting hormone onto a plastic plate or dish and dip the offset in the powder. Set the offset in the ready pot, pushing it into the dirt slightly so the cut end is in the dirt and the offset stays erect. Water sparingly so the soil remains moist but does not become moist or sloping during the rooting period.

Layering Technique

Layering allows the offset to form roots before you remove it from the mother, which can give you a greater prospect of success. Do the layering in spring. Moisten a small few sphagnum moss and pack it loosely round the base of the offset. If possible, lift the offset slightly out of the ground, but leave it attached to the mother plant, and that means that you are able to put some moss beneath it. Dust the bottom and lower sides of the offset with the rooting hormone powder, using a clean, dry paintbrush, to encourage it to set roots in the moss. Water the moss to moisten it only when it has almost completely dried. You can cut the offset in the mother plant and transfer it to the ready pot after the offset starts forming roots that are visible.

Caring for Offsets

Few pests or diseases influence ponytail hands should you permit the soil to dry out between waterings. Overly moist dirt can cause the offset to decay during and after rooting. It can take four weeks or longer for root growth to begin on the offset. During this time period, provide the ponytail palm with bright, indirect light and monitor the moisture in the soil or moss daily. You are able to move the plant to immediate, all-day sun after it roots and starts putting on busy new growth. Transplant the offset outdoors into a sunlit, well-draining bed the following spring if you want to grow it as an outdoor plant.

See related

How Shield Daisy Petals From Earwigs

When you are half crazy over the love of daisies, having earwigs chew your darlings’ petals ragged won’t do. Among the countless daisy varieties, sturdy Shasta daisies (Leucanthemum x superbum) perennial in U.S. Department of Agriculture plant hardiness zones 5 through 9 are specific earwig favorites. By bringing tachinid flies to prey on their petal-munching 23, in one of the ironies of Mother Nature , Shastas avenge themselves.

Assessing the Intruders

Check that they are actually accountable, before blaming European earwigs — that the species in Mediterranean climates — for the harm to your daisies. After dark shred daisies Much like snails, slugs and earwigs. The petals are typically eaten by earwigs, but slugs and snails eat foliage and stems, leaving shiny slime trails. Examine your plants at night by flashlight to ascertain the culprits.

Send Them Packing

Maintaining earwigs off your petals starts with keeping them. Earwigs spend their days sheltering in damp places. Your garden mulch , logs, dense ground covers or blossoms, heavy weeds and even rocks might be shielding hundreds of the pests. As you can, Eliminate as many potential hiding places, water through the day and keep the mulch as dry as possible. To other places, you may be abandoned by the earwigs without pay that is daytime.

Trapping Approaches

The next best thing to removing earwigs’ hiding places that are real would be to tempt them into ones. Remove by a small cans of tuna. Sink the cans that are open up to their rims in the soil around your daisies, in which the pests can dip into them and float. There is A less pungent alternative to wet several 1-foot spans of rubber hosing and scatter them near the daisies to your earwigs to conceal in after feeding. Shake the bugs into a container of water.

Conquer’Em With Bait

Create slow-acting earwig bait of 1 teaspoon of boric acid powder 2 tablespoons of oat bran. Place it into a box with pencil holes punched along the sides. Set the box near the daisies and pay it with a plate. Earwigs eating the bait take as much as a week to die.

Fight ‘Em With Flies

Flies are featured by the ones if earwigs have migraines. Tachinid fly larvae tunnel into after hatching from eggs their moms paste to the insects and devour them in the interior. What look like houseflies feasting on your own daisies’ nectar are your personal pressure. To boost the flies’ numbers, scatter yearly golden-yellow plains coreopsis (Coreopsis tinctoria) and white, pink or reddish cosmos (Cosmos bipinnatus) among your daisies.

In Defense of Earwigs

Unless your tattered daisy petals have you in tears, then consider the benefits earwigs bring into the garden. They prefer to consume the aphids that distort, other crops and yellow stunt and wilt daisies. Essentially harmless to people, earwigs are very likely to pinch just if sat inside clothes trapped. They also eat decaying organic matter, therefore its decomposition is sped by adding them.

See related

Craftsman Push Mower Throttle Problems

After the throttle on a Sears Craftsman drive lawn mower doesn’t work correctly, it’s hard to control the speed of the machine’s motor and cutting blades. A simple modification of the lever ought to increase or slow their speed. When the controller of your Craftsman mower has a issue, grab a few straightforward tools instead of taking the mower to a repair shop and learn more about the situation yourself.

Signs of Throttle Issues

There is A throttle issue typically straightforward to spot at a drive, such as a Craftsman version. Issues with the lever are common causes of throttle problems. Either when it’s shifted from one place to another 27, the throttle is stuck onto a single setting or fails to cause a reaction in the motor. The cable may be dislodged, faulty or stretched and fails to elicit the response when corrected.

Throttle Lever

Start the mower’s engine before making assumptions about the cause of the problem, and also correct the lever. In the event the engine reacts to all those positions that are different because it should, it will increase or decrease in speed, or revolutions per second. If the engine doesn’t sound different after you move the throttle to distinct positions, then switch off the motor and assess whether the throttle cable is on the lever on the bottom of the lever housing. Reconnect it, if the spring gets dislodged. If the lever is stuck having a brush can remove gunk or all dirt. Give the lever a squirt of lubricant, let it soak in for five to ten minutes, start the engine and then move the lever to different positions to determine whether the motor’s speed increases or decreases. If everything else fails, replace the lever.

Throttle Cable

Its cable can fail to operate Following your Craftsman push mower has had significant usage. Examine the spring that connects the cable to the lever to make certain that it’s not broken, stretched, missing or bent. If the cable is too slack, loosen the screw that holds it in place, reposition the cable to make it tighter and then tighten the screw to maintain the place. If the cable is too taut, then could be loosened tightened to maintain the cable at that position that was looser.

Throttle Arm

After spring the cable and lever seem to be in working order, the issue may be using the arm. Determine whether the arm opens and closes the throttle as it should. Then substitute it with a brand new one if the arm is broken or bent. Most socket versions require removing the air filter cover and air filter to get.

See related

What Makes Some Dirt Red in Color?

Some soils are distinctively red in color while others are brown or black. Colour is determined by numerous things, including mineral makeup conditions, weathering and content. Many red lands, such as Georgia’s famous clay, acquire their color by the presence of iron oxides. Gain useful insight into the characteristics of your soil by knowing what its color means.

Soil Color and Drainage

Patterns and color found inside the subsoil offer significant clues to some soil conditions. While soil will be dull and dark well-drained soil is brighter in color. Vibrant red colour results from iron. Waterlogged, anaerobic conditions retard oxidation, leading to dull yellowish-colored or gray soil. Bright red or brownish-red subsoil generally indicates good motion of air and water. Undergo periods of standing water or soils that drain slowly develop mottling that may include both brightly colored brown and red stains mixed with dull gray stripes and spots.

Organic Content

Colour is a good indicator of organic content–the amount of decomposed plant and animal material . Dark brown or black topsoil contains a high proportion of organic matter. Excessively moist soils tend to retard the formation of colours, but don’t necessarily indicate a deficiency of iron. Soil of any color indicates a proportion of organic matter. Wind, sun and water erosion reduce content, leading to soil.

Parent Material

Colour is associated with the parent material from which it was formed. Red soil might be derived from stone, such as the sandstone common into the desert areas of Nevada, California and Arizona. Hematite — that the mineral from which iron ore is obtained — is a frequent source of color for many lands, particularly those in zones or dry areas. Red soil may come and manganese because the stone is broken down through weathering which become oxidized. For instance, the land of the Piedmont region of Georgia was made from deposits of gneiss and white, black and gray granite. Over time, the rock material was reduced to dust, including oxidized iron which colored the soil red.

Ultisols

Occasionally called”red clay lands,” ultisols are among the 12 orders of land, identified by the U. S. Department of Agriculture’s Universal Soil Classification System. Reddish in color, ultisols are located in portions of Africa, Asia and South America and hot, humid areas such as the Southeastern United States. These lands are often highly acidic and form in extremely weathered geologic areas. If correctly amended with lime and fertilizer, ultisols are low in nutrients and contain high amounts of clay but may be utilized for agriculture.

See related

How to Grow Orchids From Cuttings

When most orchids (Orchidaceae) are only hardy in U.S. Department of Agriculture zone 10b, the vivid flowers make excellent indoor specimens when given sufficient soil and moisture. In case you have one of over 1,200 species of Dendrobium orchids, then you can propagate the plant to grow orchids that are several with exactly the very same features as the mother plant.

Cut a stem on your own forehead at least 12 inches long near the base using pruning shears or a sharp knife. Split the stem into 3- to 4-inch segments, making sure every segment has a dormant bud.

Line a shallow tray with sphagnum moss, until it is thoroughly moist, and mist the ribbon. Place the cuttings in the tray. Cover with polyurethane plastic wrap and place in a place that’s at least 60 degrees of direct sunlight.

Fill one 3- to 4-inch pot per orchid plantlet with fir bark potting mix to within an inch of the top of the container. Place one in every container, then covering the stem segment and roots with potting mix When the orchid stem plantlets have sprouted in the buds.

Line a tray with smooth stones and add sufficient water to almost cover the stone. Put the pot on top of the rocks to keep the atmosphere round the humid. Keep your fresh orchids in an area which receives mist them every day, and bright, indirect light. Orchids prefer temperatures between 55 and 80 degrees Fahrenheit depending upon the species, and a night temperature of 50 degrees for optimum flowering.

Water your orchids from the drainage holes per week until water flows and fertilize every three weeks with a orchid fertilizer from spring into mid-fall. Alternately, dip the base of the container in a bucket of water, letting it soak through the holes.

See related

How to Set Linoleum Tiles on Concrete

If your real estate investment has a basement or living room with concrete floors, you may want to install linoleum tiles across the cement heat up the area and to add interest. When you consider linoleum, you may recall geometrical patterns and 1970s schemes, but modern linoleum tiles resemble granite, marble and woodgrains. Linoleum tile installation demands measurements that are proper and tiles to guarantee a smooth flooring surface that is functional and modern.

Snap a chalk line from the middle of one wall into the middle of this wall that is parallel. Snap another chalk line from the middle of the vertical wall into its wall that is parallel. This creates four flooring segments that are equivalent.

Lay loose linoleum tiles in all directions from the middle point. Examine design and the fit of the tiles. If the tiles do not fit and there are tiles that you want to reduce bigger than 1/2 inch across the room’s perimeter, reposition your centre starting point. Re-snap the chalk lines to adapt to the new design.

Apply latex adhesive, with a notched trowel, to the centre intersection. Avoid covering the chalk line. Press it in a portion of the adhesive over the middle chalk line As soon as you place your tile. Apply latex adhesive in 2-foot squares as possible work. In each quadrant, row by row, working toward the wall on all four sides secure the tiles. Follow the directions on your latex adhesive to be sure you use the correct quantity of mix on the tiles.

Cut the linoleum in the wall using a utility knife. Guarantee that the linoleum slides under any baseboards. Cut the linoleum so that it’s flush against the walls or slides under the little crack in the wall where the wall meets the ground.

Roll the tiled surface using a roller. The pressure prevent undesirable bubbling, warping and peeling of the linoleum and will fasten the tiles into the ground. Make sure that the flooring manufacturer doesn’t discourage rolling your brand and version of linoleum with the roller.

Allow the linoleum prior to putting furniture to dry. FindAnyFloor.com recommends letting the linoleum adhesives cure for 24 to 72 hours. Avoid walking round the linoleum-tiled surface.

See related

The Way to Install a Fluorescent Light Fixture Underneath Cabinets

Lights create work and accent surface lighting for kitchen counters. In addition to incorporating a focal point to a darkened area of a space, the long ballast layout of fluorescent light fixtures ensures a vast majority of the counter area beneath the cupboard is fully illuminated. Fluorescent light fixtures are simple to install and eliminate shadows created by cabinets.

Find an electric outlet or light fixture near the cupboard where you want to install the light fixture, to use as a power source.

Put on rubber insulating electrician gloves and rubber bands to prevent electrocution. At the primary circuit breaker box, then find the circuit breaker for this area of the home. Open the circuit breaker panel with a screwdriver. Find the circuit breaker that is connected to the electrical outlet or light fixture near the cupboard where you’re going to install the fluorescent light. The circuit breaker is under using a multimeter. Twist the red lead of the multimeter. Twist the black lead into the metallic floor bar on the side of the circuit breaker box to floor it and have a reading of this circuit breaker amperage. Insert the amperage rating of this fluorescent light fixture into the circuit breaker amperage measurement to find the total amperage. If the total amperage is equal to or less than 80 percent of the circuit breaker’s amperage rating, the light can be wired into an electric outlet or light fixture connected to this circuit breaker.

Turn off the power in the primary circuit breaker into the space which you are going to be installing the light. Twist the black lead to a neon tester into the twist on the face plate of the electric outlet to floor it and insert the red neon tester lead into the right slot of an electrical plug opening on the outlet. If the neon tester doesn’t light up when you touch the tester leads to the electric outlet, the power is off and it is safe for you to install the light.

Find an area on the wall, either under or near the cupboard which you are going to install the light fixture, to place the light switch. Run a finder along this area of the wall. Use the finder to find an stud if you find a stud. Studs generally are spaced 16 inches to 24 inches apart from each other in the wall. Make a mark on the wall beneath or near the cupboard that is halfway involving the two studs in the switch height that is desirable or 44 inches upward from the ground using a pencil. Put the switch box that is light on the wall, based over the pen mark and trace around it with a pencil. Cut on the reflective line using a keyhole saw and remove the drywall. Slide the switch box into the hole you just cut together with the open side facing you to make sure that it matches and then set it aside.

Hold the light fixture up from the underside of the cabinet base and use it to ascertain where you have to drill a hole to the cable. If you can align the cupboard hole position together with the light switch hole place it’ll make feeding the electric cable through the walls simpler for you.

Remove the screws and gently pull it. Route a span of the cable in the change hole through the wall into light fixture or the electric outlet. If the electric outlet or light fixture is positioned higher in the space than the light switch hole, then begin routing the cable through the wall or ceiling from that place instead. Pull the cable out of this light switch opening with fish tape. Cut the cable with cable cutters, leaving a surplus of 6 inches of electric cable.

Route a length of electric cable in the fluorescent light hole in the cupboard to the light switch hole in the wall. Pull the cable so there is just 6 inches of cable then cut the cable using cable cutters.

Strip 3 inches away from the exterior insulation jacket of every end cable with cable strippers to show the colour. Strip 3/4 inch of the insulating coat from the end of every cable.

Drill pilot holes to the light fixture mounting screws. Have a helper hold the fixture since you drive the screws into the cupboard using a screwdriver. Route the cable through the cable opening in the light fixture home.

Hold the wire end of this fluorescent light fixture together with the cable end of the cable and twist them together. Screw an electrical wire nut onto the ends of the wires and fully cover the exposed metal of the cables together with the cable nut. Twist together the black cable end of this fluorescent light fixture using the black cable end of the cable and cover the connection by screwing on a wire nut. Wrap the bare copper ground wire of the cable clockwise around the green grounding screw on the light fixture. The grounding screw to secure the grounding cable.

Cut a piece of electrical cord. Remove of this cord and separate the wire, the wire that is black and the bare grounding cable. Cut the black and white wires in to two 6-inch pieces. Strip off 3/4 inch off the insulation of the cables.

Attach the electric wire resulting in the fluorescent light fixture along with the power source (electrical outlet or light fixture) cables into the light switch making a”pigtail” together with the wires. Hold the cable end leading the cable end resulting in one conclusion of a piece of black cable and the power source together, to the light fixture. As necessary with cable cutters to make them even the wire ends and cut. Twist the cable ends. Twist a cable nut to link them. No bare stripped cable will be observable beneath the cable nut when done properly. Wrap the free end of this black wire that is 6-inch clockwise around the positive terminal twist on the light switch and tighten the screw to secure the wire. Pigtail the wires in the identical way to attach them to the neutral terminal twist of this switch.

Strip 3/4 inch the insulating coat of this green floor wire pigtail with twist from. Hold the ground wires of the cable resulting in the light fixture along with the power source cables into the light switch with the ground cable pigtail and twist them together. Screw the grounding cable nut onto the twisted ends of floor cable. Add the screw end of the ground cable pigtail into a hole on the box and tighten it with a screwdriver. Gently push all of the cable pigtail connections into the box and insert the light switch. Screw the light switch into the box and put in the light switch cover.

Attach to the electrical outlet power source. Electrical sockets have a pair of terminal screws on the right and left side to permit for the outlet to be connected to a primary power source and to”string” the power along to another electric outlet or light switch. The outlet will have a grounding, white and black cable already attached to one pair of terminal screws; leave these wires in place. Wrap the wire clockwise round the unused twist terminal of the electric outlet and tighten the screw. Wrap the wire clockwise around the impartial screw terminal and tighten the screw. Pigtail the ground cables as before. Gently push the wires into the box and reattach the outlet then reinstall the outlet cover. Pigtail the black and white wires as before using a piece of color coded wire When the outlet has cables attached to all of its terminal screws. If you’re attaching wires into a light fixture rather than an electric socket, then twist screw on a wire nut and the cable ends of the light switch and light fixture together. Do the same with the wires of light fixture and the light switch. Twist together the floor wire leading to the light switch, the light fixture along with the 6 inch’s ground wire ground wire pigtail using twist. Gently push the wires up into this fixture’s electric box and then reinstall the light fixture cover.

See related

The Way to Install Garden Path Lighting

Garden path lighting is a tiled option for front, side and backyards that creates a light source that is gentle. The light highlight decoration plants will illuminate your walkway, create ambiance illumination and prevent damage to plants which line the trail. Garden path lighting options include a rainbow of colors in electric or powered alternatives. Lighting is available in various heights, wattage and mounting alternatives. Timers wired to either option provide light when needed.

Mark the garden light route with a can of spray paint.

Dig at a 12-inch deep trench along the entire length of this garden light route.

Lay the light fixtures along the road, spacing the fittings.

Lay cable along the length of the trench to an electric outlet located 10 feet from the lighting fixture.

Switch the power to the outlet off. That power is off using a circuit expert.

Mount a transformer to the outlet.

Strip 1/2-inch on the finish near the transformer from the conclusion of this 12-gauge cable. Loosen the terminal screws onto the base of the transformer. Slide the wire that is stripped under the terminal screws. Tighten the screws across the wire.

Stand the light fixtures. Examine the spacing until the base of the light fixture will be flush with the garden surface and push the stake of this light fixture to the floor. Repeat this process are set up.

Independent the connector halves attached to the lighting fixture. Twist the top of the connector over the 12-gauge wire. Twist the bottom half over the opposite side of this 12-gauge wire. Until you hear a click, push the two connector halves together. The connector pliers are made to pierce the power wire to create contact. Repeat this process are connected to the cable.

Turn on the power to the electric outlet.

Plug the transformer. Assess each light to ensure power flow. Unplug the transformer if power flow is not current, separate the connector halves and reconnect them. Where the link was attempted to protect the integrity of this wire, wrap electrical tape around the wire.

Lay connectors and the 12-gauge cable . Bury the cable and connectors. Change the depth of the wire to prevent pulling and tilting of the light fixture.

See related